2013 Duramax Nox Sensor Replacement

2013 Duramax Nox Sensor Replacement. Where is a knock sensor for a 1994 chevy where is a knock sensor for a 1994 chevy 1500 5.7 v8 2wd 1/2 ton located. The nox sensors are getting replaced as soon as dealership gets them in and calls me to set up an appt.

Upstream Nox Sensor For GM Diesel 6.6L Duramax Chevrolet from www.ebay.com

It looks to me like you do not have a nox sensor fault at all. I have a 2013 chevy silverado 2500hd duramax. The repairs will be made at no charge to the customer.

Source: www.aliexpress.com

So, im pretty much decided on saving my money and deleting my 2013 gmc sierra duramax. Dealers are to replace the nox sensor.

Source: www.ebay.com

I did have to use quite a bit of force to remove it but it did come out. Title (customer effect) selective catalytic reduction ( scr ) efficiency and nox sensor codes.

Source: ekgdiesel.com

A circuit or performance condition with a nox sensor is detected by the nox sensor module. The nox sensors are getting replaced as soon as dealership gets them in and calls me to set up an appt.

Source: www.lynol.net

This video goes over the replacement of the rear nox sensor. From the limited information i have, i can guess that your nox sensors are working correctly, but it is not sensing enough of a nox reduction.

Source: www.ebay.com

2013 gmc sierra full delete. If there's only a check engine light and a code, but no message or restriction, then replace the sensor, clear the code.

Source: www.ebay.com

First off, there's 2 nox sensors, so replace the right one (or both if you wanna be extra safe). From the limited information i have, i can guess that your nox sensors are working correctly, but it is not sensing enough of a nox reduction.

The Smart Nox Sensors Consist Of Two Components, The Nox Module And The Nox Sensor Element That Are Serviced As A Unit.

Try running another diagnostic test to ensure that your device has been correctly repaired and is in full working order after you’ve placed it back into your vehicle. It took me about an hour and a half, pretty simple actually. If there's only a check engine light and a code, but no message or restriction, then replace the sensor, clear the code.

I Replaced The Nox#2 Sensor Myself.

If the truck is in restriction, then it depends on what code (s) are stored/which message is on the dash to get a reset strategy. Nox2 is the forward of the two sensor bodies. Now that you’ve replaced the probe on your nox sensor, this should be the end of your diagnostic issues!

Enter Your Ride Here To Be A Part Of This Months Ride Of The Month Challenge!

Jump to latest follow hey everyone! From the limited information i have, i can guess that your nox sensors are working correctly, but it is not sensing enough of a nox reduction. This video goes over the replacement of the rear nox sensor.

A Circuit Or Performance Condition With A Nox Sensor Is Detected By The Nox Sensor Module.

Nox sensor can accurately and quickly measure the nox concentration in the gas, the sensitivity is good, the nox shows a reliable selectivity. Im new to this whole process bc ive never owned a diesel. It looks to me like you do not have a nox sensor fault at all.

Where Is A Knock Sensor For A 1994 Chevy Where Is A Knock Sensor For A 1994 Chevy 1500 5.7 V8 2Wd 1/2 Ton Located.

Discussion starter · #1 · oct 23, 2015 (edited) the repair for nox sensor #2 is identical to the replacement instructions for the particulate matter sensor with the following amendments: Nitrogen oxide sensor replacement for duramax diesel 6.6l 12642311 5wk96645c. Installed this on my 2013 gmc 3500 duramax.